Pourquoi votre micro dynamique manque de gain et comment y remédier

Why your dynamic microphone lacks gain and how to fix it

LCREA Paris - Microphone Manufacturer
Figure 1 The Picomix plugged directly into the microphone: preamp amplification built into the XLR connector.
You have invested in a good dynamic microphone. You plug it in, push the gain on your interface to the maximum, and the level remains low. Worse: hiss appears, that continuous background noise that pollutes everything you record.

This is not a fault of your microphone. It is not your mistake either. It is a structural problem, known to all sound engineers, and it has solutions.

Where the problem comes from

A dynamic microphone works without active electronics: a diaphragm moves a coil in a magnetic field, and this movement generates a current. It is a robust, reliable principle, capable of handling enormous sound levels without distortion, which is precisely why they are used on stage and in broadcasting.

But this principle has a downside: the signal produced is very weak. Where a condenser microphone delivers a comfortable level, a dynamic microphone outputs a signal that is sometimes ten to twenty times weaker.

To make use of it, it must therefore be heavily amplified. And that is where the trouble begins.

Figure 2 Pushing the gain to the interface's limit amplifies the self-noise as much as the voice.

Why hiss appears

Every preamplifier adds noise. It is inevitable: it is physics, not a manufacturing defect.

As long as you amplify moderately, this noise remains well below your signal and you do not hear it. But when you push the gain to its maximum, what is required by a low-sensitivity dynamic microphone, you amplify the noise as much as the voice. The ratio between the two does not improve: it degrades.

On an entry-level or mid-range audio interface, the phenomenon becomes audible around 55 or 60 dB of gain. Yet this is precisely what an SM7B or a RE20 needs for spoken voice.

In other words: it is not that your interface is bad. It is that it is being asked to work at the limit of its capabilities.

Figure 3 Acompact JFET preamplifier housed directly in the XLR plug.

The three solutions

1. An interface with better preamps

This is the most obvious solution, and the most expensive. Professional interfaces have preamps capable of providing 65 to 70 dB of clean gain. The advantage: you improve your entire chain. The downside: the high cost and the unnecessary replacement if your current equipment is otherwise suitable.

2. An external preamp box

It is placed between the microphone and the interface, providing 20 to 30 dB of clean gain. The advantage: compatible with all interfaces. The downside: a box to place, two cables instead of one, and an additional point of failure.

3. An amplified cable

The principle is the same as the box, but the electronics are built into the cable connector. You replace your XLR cable, and the gain is there, powered by the 48V phantom power of your interface. The advantage: no clutter. The downside: the gain is fixed.

How to choose

If you regularly change microphones and work with multiple sources, a good interface remains the most versatile investment.

If you have a stable setup, one microphone, one interface, and a recurring use such as podcasting or voice-over, the cable-integrated solution is the simplest and least cluttered.

And if you use a ribbon microphone, one additional point deserves attention: these microphones are particularly low-sensitivity, and some are fragile when exposed to poorly managed phantom power. Check that the chosen solution ensures their protection.


What we make

We designed the Picomix based on the third approach: an XLR cable integrating a JFET preamplifier, powered by 48V phantom power, which provides 15 to 18 dB of clean gain and protects ribbon microphones.

We did it because we were ourselves facing the problem, and the idea of adding another box to an already crowded setup did not suit us.

It is handmade in our Bordeaux workshop, available in three lengths and seven colors, starting at €99.

Figure 4 Detailed view of the JFET preamp circuit housed directly inside the Picomix cable connector.

Give your microphone clean gain

A raw audio sample, with and without Picomix, is available on the product page. Listen before deciding.

 DISCOVER THE PICOMIX →
Back to blog